Polyethylene Infusion Flow Tubing: Resin Feed and Vacuum Line
The feed and vent lines that carry resin through every infusion.
Polyethylene infusion flow tubing is the flexible line that carries resin from the pot to the laminate and pulls vacuum from the bag to the pump. Resin does not bond to polyethylene, so the tubing releases cleanly after cure. As a result, it suits vacuum infusion in marine, wind, automotive, and structural composite work. Furthermore, its chemical resistance covers polyester, vinyl ester, and epoxy systems.
Why Tubing Choice Matters in Infusion
Every infusion depends on controlled flow. Tubing that kinks, collapses under vacuum, or bonds to cured resin ruins the set-up. Consequently, fabricators choose tubing that stays open, holds a seal, and peels free of the laminate.
Polyethylene handles all three jobs. It stays flexible enough to route around moulds and fittings. Moreover, it resists the resins and solvents common in composite shops.
You can also cut it quickly with a sharp blade or tube cutter. In addition, a clean square cut seals well against sealant tape and spiral or omega fittings. That keeps the bag airtight and the resin front predictable.
Key Performance Advantages
- Resin release: cured resin does not bond to polyethylene, so lines peel away cleanly
- Chemical resistance: handles polyester, vinyl ester, and epoxy resin systems
- Flexible routing: bends around moulds, corners, and fittings without fuss
- Holds vacuum: stays open under bag pressure when sized correctly
- Easy to cut: a sharp blade gives a clean, square end for sealing
- Versatile use: works as a resin feed line, a vacuum line, or a catch pot connection
- Pairs with standard consumables: suits sealant tape, infusion mesh, spiral wrap, and vacuum fittings
Where Flow Tubing Fits in an Infusion Set-Up
| Component | Role in the Bag |
|---|---|
| Flow tubing (feed) | Carries resin from the pot into the laminate |
| Flow tubing (vacuum) | Connects the bag to the catch pot and pump |
| Infusion mesh | Spreads resin across the part surface |
| Spiral tubing | Distributes resin along a line |
| Sealant tape | Seals the bag film around the tubing |
| Bagging film | Holds vacuum over the laminate |
| Peel ply | Leaves a clean, bondable surface |
Tubing sits at both ends of the infusion path. However, a good result also depends on clean seals and correct tube sizing for your part.
Typical Applications
This tubing suits any vacuum infusion set-up that needs reliable resin and vacuum lines:
- Marine & Boat Building: hull, deck, and bulkhead infusion
- Wind Energy: blade shells, spar webs, and prototype components
- Automotive & Motorsport: body panels and structural parts
- Aerospace & UAV: skins, fairings, and lightweight structures
- Construction & Infrastructure: GRP panels and sandwich components
- Tooling & Moulds: infused mould skins and backup laminates
- Repair & Prototyping: small infusions and test panels
Technical Specifications
| Property | Specification |
|---|---|
| Product | Polyethylene infusion flow tubing |
| Material | Polyethylene (PE) |
| Compatible Resins | Polyester, Vinyl Ester, Epoxy |
| Primary Use | Resin feed and vacuum lines for infusion |
| Compatible Processes | Vacuum infusion |
| Sold As | Per linear metre |
Contact Enhanced Composites for sizes, roll pricing, and current datasheets.
Frequently Asked Questions
What is infusion flow tubing used for?
It carries resin into the laminate and draws vacuum from the bag. Fabricators use it on both the feed side and the vent side of an infusion.
Does resin stick to polyethylene tubing?
No. Cured resin does not bond to polyethylene, so lines release cleanly and often reuse or trim away easily.
Which resins is it compatible with?
It works with polyester, vinyl ester, and epoxy resin systems.
How do I seal tubing through the bag?
Wrap sealant tape around the tube and fold the bag film into pleats around it. Use fittings or spiral tubing at the ends for a better seal.
What size tubing should I choose?
Match the tube to your part size and resin viscosity. Larger parts and thicker resins usually need a wider bore.
Why Enhanced Composites
Enhanced Composites stocks vacuum infusion consumables as live inventory lines, with no minimum order. Additionally, the range covers infusion mesh, peel ply, bagging film, sealant tape, and resins. So your full infusion kit can come from one trade account.
Bulk pricing and sizes: email info@enhancedcomposites.com.au
Peel Ply Nylon 60gsm - 1.5m width
Unidirectional Carbon Fibre Tape 300gsm - 100mm wide
Sealant tape - Black - 15m 



